I am so happy to say this project is done. It looks gorgeous and we actually enjoyed our backsplash project.
Now, that’s not to say it didn’t take a lot longer than I anticipated. I don’t know where I got the idea this would be a one-day on a Saturday project. Ha. But, as I have been learning on our kitchen makeover, it is best to be patient and do things right. And not go crazy when things don’t get done as fast as you thought lest you will drive your husband insane and he will not want to do this. I wasn’t always sweet or charming, but we worked together. Ah, marriage.
I read a lot of tutorials on blogs about doing a subway tile backsplash before we started. You know, to make sure we could do this. We could. We did. And you can, too.
I measured our backsplash and determined how many square feet we needed. Then I figured that I can fit 8 of the 3”x6” tiles in one square foot and figured I would need around 200 tiles total. We bought the $0.22 ones from Home Depot- Daltile in white. We bought extra in case some broke or we mis-measured. And I grabbed a few bullnose tiles ($0.74 each) for the edges where the tile would end in the middle(ish) of a wall.
- Tiles (“White modular tile”) -222 tiles $48.84
- Bullnose tiles- 8 = $5.92
Other supplies we bought for this project:
- 1/16” spacers- 2 bags at $2.97 ea
- Thin set at $21.97/gal- white
- Notched trowel appropriate for our size tiles $2.96
- 10 lb box of unsanded grout in bright white (to know why I picked white grout read here) $13.47
- Sealer ad-mix $9.97
- Grout float $9.97
- Rosin paper- $11.97
- Grout caulk, bright white $7.23 x2
- Sponge $2.47
- Cheesecloth $3.97
- Wall repair patch $4.37 to cover old cable plug
Other tools/supplies we used included (but didn’t purchase):
- Spackel to patch dry wall
- Power sander
- Putty knife for spreading the thin set
- Wet tile saw
- Tile nippers
- Dry erase marker to mark where to cut tile
- Blanket for my hubby to rest his knees on
- 5 gallon bucket
Whew. So we started by removing our laminate backsplash and sanding off all the pieces that were peeling. Then we spackled over any divets in the drywall and sanded again. This made a HUGE mess. Ugh. We also covered an old cable outlet with a drywall patch.
So there is a little silver metal sliver that was in the corner of the laminate that is unable to be removed without peeling up the counter. I have never seen this in a house before. But, it had to stay. This proved to be somewhat useful in the tiling process as long as we were able to cover it with grout and caulk!
So, we used it as a resting place for the bottom row of tile, which was actually convenient. We started with the tiles on the bottom and moved up so any short pieces were under the cabinet and not very visible.
In the photo above, the vertical tiles are the bullnosed ones which made for a good end to the row that didn’t abutt the wall.
Our setup was that I spread the thinset and did the notching and gave it to the hubs who placed it and the spacers and made sure they were level and properly aligned. We made sure the brick pattern was even by using a level to make sure the spaces from row to row lined up.
He was also the lucky one who measured and cut for the wonky areas around outlets.
It got tricky on the far right of the photo below since it steps down from the main part of the kitchen. We continued the bottom row of tiles over from the main part, which became the middle of the wall, and then went down. We trimmed the bottom row of tiles to make it fit (which was just like a shaving and barely noticeable).Laying all the tiles took parts of 3 days, maybe about 20 hours total? It went faster as it went on because we got better, but there were a lot of skinny cuts to make.
After letting the last laid tile set for at least a day, we went for the grout. I don’t have any photos of this because it was a mess. And a lot more difficult than I anticipated. And my camera photo card was missing.
We mixed it according to the ad-mix (it changes the water content added) and grout box. It was about as thick as toothpaste. Then we spread it with the grout float at a 45 degree angle, making sure it got in all the cracks.
We made the mistake of spreading it all over the kitchen before wiping it off. What would’ve made more sense and been easier would be to spread the grout in a small area at a time and wipe it off. By spreading it all over we then had to work really fast to wipe off all the excess grout with the sponges and water before it hardened. This part was harder than I thought too. After we wiped off the excess we let it dry for a few hours and then buffed off the haze using the cheesecloth so the tiles shone.
Finally we used the tile caulk along the bottom to cover up the silver thing, along unfinished sides, and the top under cabinets. It made our work look complete.
Oh and these little rows of tiles? Well see where the previous backsplash was before in a triangle shape? I was at a loss for a while of what to do there. Continue from the same height under the cabinets? Do nothing? Well I decided to do just 2 rows on this wall and the one by the coffee pot so that it look finished and yet not weird to have a half-wall of backsplash with nothing over it.
Total this project stretched over about a week. Like I said, for the most part we enjoyed it. But more than anything, we love how sleek our kitchen looks now!
Our kitchen makeover is almost done, we have been working on painting the cabinets and picking a color for the walls. We are heading to Chicago this week for a conference for my work and the hubby is tagging along so we can have a little vaca as well. I bet we will be excited to finish up the kitchen when we get back!
What do you think of our backsplash? Pretty awesome look for the price ($167) don’t you think? Are you wanting to re-do your backsplash? I would love to hear about it! If you have any questions about our process feel free to comment!
Linked up to Thrifty Decor Chick’s May Before and After Party
Linked up to Liz Marie Blog